ContactJackson / Charvel JT6 Floyd Tremolo Bushings Covers available!These originally came on the earlier USA Models that had the JT6 tremolo installed to cover up the "sloppy" paint edge around the bushing hole. These were lightly pressed into the paint but would usually come lose and get lost if removing the trem for maintenance.Bushings without bushing covers:Bushings with theBushing covers installed:$10.00 per pairJCH-2CJackson JT6 Bridge String Lock Screws!Available now are these Replacement String Lock Screws for the Jackson JT6 Tremolos. Remember, the whole reason these have to be replaced is because everyone seems to want to over tighten this screw. There is no need for that ;o)These are $4 each or a set of 6 for $17.00 or: The set of 6 with Allen Wrench is $18.00As you can see in the pic (above right), while they do look different, they're not bad at all and have a nice black finish to match. I was going to start "kinking" the last thread near the wrench opening but thought some of you might actually like the fact that the fine tuner can turn right off. If you'd like this little feature, just give me a shout and let me know and I can do that for you so you don't lose your fine tuner on stage ;o)Screws may not look like perfect reproductions, but these are the closest to original you will find in fit and fiinish.Solid Aircraft Aluminum tremolobar Friction Collar for the Fender System 1 tremolo.These are a direct replacement and a much better upgrade as you do not need a separate tool to tighten the collar. Just tighten up the nicely knurled collar and put the bar where YOU want it! Natural and Black anodized aluminum now available!$25.00 eachHWSYS1FCNaturalAluminumBlack AnodizedAluminumSystem I Trem arm bushingsThese are the plastic bushing that fits between the round, chrome friction nut and the arm socket in the base plate. Angled side faces up into the Friction Collar.The bushing is the black ring in the photo (right).$15.00 eachHWSYS1FBFender System I Stainless Steel Fine Tuners These are made from solid stainless steel and are not soft and weak. These are not original replacements, but have the exact thread size, and fit and function correctly.Fender Elite Bass Stainless SteelFine Tuners $6.00 each screwHWft-2B$6.00 each screwHWft-2Also available in sets of 6 for $28.00These have domed thread ends and are made from solid stainless steel and are not soft and weak.These are not original replacements, but have the exact thread size, and fit and function correctly.Kahler 2300 &2500 (Tremolo), Flyer, & 3300 (Fixed Bridge) Stainless Steel Fine TunersThese are made from solid stainless steel and are not soft and weak like the brass screws.Also available in sets of 6 for $28.00$6.00 each screw HWft-1Washburn Wonderbar Tremolo Socket BushingsThese are the little black bushings that tighten up the trem arm when turning the "friction" collar around the arm. 1 Required.Angled side faces down into the Tremolo bar socket.$15.00HWWFB$25.00 eachBlack AnodizedAluminumHWwfcr-BASolid BrassHWwfcr-BRWashburn Fine Tuner WashersThis is a set of 6 Black Delrin Washers for the Washburn / Shift 2001 Tremolo. These are the thin black washers that act as cushions for the fine tuners.$12.00 for the set of 6 pcsTB-FTW.Washburn Wonderbar Height Adjusting ScrewsThese are the Front (long) HWhwl-1and Rear (short) HWhwl-2 height adjusting set screws.(Please enlarge picture to the right) These are the same exact size and fit that you need for those lost or rusted screws.$2.00 for eachset of 6 pcs.Front (long)HWhwl-1Rear (short)HWhwl-2OR$4.00 for eachset of 12 pcs.Front (long)HWhwl-112Rear (short)HWhwl-212JT6 and Ibanez Trem Socket Spring ScrewsThis is the screw that holds the spring and is a perfect fit for the Ibanez edge and JT6 tremolo sockets..50 cents each HWsc-21Floyd, Schaller, ESP, Takeuchi, Ibanez Edge, Washburn 600S, and JT6 Tremolo Intonation Screws.A note on the JT6 Intonation screws. There are 4 versions of these which are the length and head style. The threaded portion of the screw had changed through production of these because Jackson changed the baseplate slot thickness for the recessed nut.You have your choice of 2 lengths and 2 head styles of these screws so please make sure you check what you need or you can shoot me an email if you need help.**Length of screw thread is measured under the head**Button Head in 8 mm (.315")Button Head in 10 mm (.394")Socket Head in 8 mm (.315")Socket Head in 10 mm (.394").45 Cents each Set of 6 for $2.50 HWsc-22(Use this part Number and tell me which Trem you have)Rockin'Magic IIIntonation Buttonhead Setting ScrewsAs found on most SE and Early RGX ModelsI had some questions about why there are saddle "rollers" on this bridge as it doesn't look like other Rockin Magic bridges. The reason is, I machined the slots and installed rollers myself to allow better string movement. Sorry about any confusion..45 cents eachHWYRM2IBSSRM-Pro TremoloIntonation or Saddle/String Lockdown Screws.45 cents eachHWYRMPSLSRM-Pro Tremolo Friction CollarsThese are the perfect replacement for the Friction Collars that seem to grow feet and walk away.These are black anodized aluminumand will fit the original RM-Pro (with Pop-in Bar).Notice, I've removed the RM Pro II (only!) from the list of tremolos that use this friction collar because apparently, Yamaha had changed design through production on these. If you'd like to take a shot at ordering one, feel free, but I can not guarantee that it will fit your RM Pro II Tremolo.$25.00 Each Black Anodized Aluminum: HWyfcr-1RM-Pro Tremolo Bar Friction bushingsThese are the Delrin bushing shown in the picture below being pointed to by the black arrow.Angled side faces down into the Tremolo bar socket.This is for the bushing only!$15.00 Each HWyfb-1Email Me: HEREWashburn Friction collars for the Wonderbar/2001/Shift tremolo are available in Black anodized aluminum or Solid Natural Brass.Original Floyd Rose Socket Swivel WashersThese originally came on the earlier Original Floyd RoseTremolos that used the screw-in type bars. These replace the worn out white washers (shown in the pics to the right).$8.00 per pairHWOFR2B$6.00HWJKSLSJackson JT6 Or Kahler String Lock ShimThese are the original thickness that cameon the JT6 and Kahler String Locks. Can also be used for the string locks I sell as wellJackson/Charvel “JT490” or “ST”and alsoIbanez Maxxas and S-440II GOTOH BridgesThese are hard to find replacement screws for these bridgesIntonation Screws 6 Pcs.$10.00Saddle Locking Screws 6 pcs. $3.00Tremolo Bar Friction Screw 1 pc. $1.00JT6 Tremolo Intonation NutsThis is the nut that fits into the recessed slot on the underside of the JT6 Jackson Bridge.These are Black Stainless Steel$1 each Set of 6 for $5.00 HWsc-22NTremolo Sustain/Inertia Block SpringsThese are the springs that connect your Sustain/Inertia block to the spring claw in the rear trem route of the body.$1.50 each Set of 5 for $7.00 HWspr- 1Original Floyd Rose Adjustable Trem StopOriginal Floyd Rose Trem Stops areinstalled in the trem Cavity to give a “bump” stopfor the inertia block on the trem. $5.99 HWFL-1Fender System I Saddle Locking ScrewsThese are the screws that lock your string saddle after setting the intonation.$2.50 perset of 6HWFsc-1Allen Wrench for Jackson/Charvel “JT490” or “ST” and Ibanez Maxxas and S-440II GOTOH BridgesThis is for the trem bar friction screw adjustmentlocation near the trem bar socket opening$1.00EachRM-Pro II and RM Pro III Tremolo Friction CollarsThese are the perfect replacement for the Friction Collars that seem to grow feet and walk away.These are black anodized aluminumand will fit the original RM-Pro II (with Pop-in Bar).$25.00 Each Black Anodized AluminumHWyfcr-3RM-ProII Tremolo Bar Friction bushingsThese are the Delrin bushing shown in the picture.Angled side faces down into the Tremolo bar socket.This is for the bushing only!These replace the “crunchy” brass original bushingsand these allow for smoother positioning of the trem bar.$15.00 Each HWyfbII-1Rockin'Magic IIString Clamp Lockdown Flathead ScrewsAs found on most SE and Early RGX ModelsI had some questions about why there are saddle "rollers" on this bridge as it doesn't look like other Rockin Magic bridges. The reason is, I machined the slots and installed rollers myself to allow better string movement. Sorry about any confusion..45 cents eachHWYRM2SLFSString locking Bolts for the Schaller Floyd Rose Bridge$2.00 EachHWFL-6SB-1or$12.00Per set of 6HWFL-6SBString locking Blocks for the Schaller Floyd Rose Bridge or Jackson / Charvel JT6 Floyd$2.00 EachHWFL-6BL-1or$12.00Per set of 6HWFL-6BLScrews may not look like perfect reproductions, but these are the closest to original you will find in fit and fiinish.$18.00 perset of 6HWFsc-6Fender System I Saddle Intonation Setting ScrewsThese are the 6 screws that set your string saddle intonation. This is a complete set ofsix screws in the correct Phillips head and full thread,finished to the 3 correct lengthsjust like the originals. Floyd Rose Lo-Pro Bridge String Lock Screws$2.00 EachHWFL-6L-1or$12.00Per set of 6HWFL-6LKahler PartsKahler Bridge Shims for the Older 2300 seriesThese are available in 1/16th, 3/32nds, or even 1/8th thicknesses. $16.00HWK-1Kahler 2300 &2500 (Tremolo), Flyer, & 3300 (Fixed Bridge) Stainless Steel Fine TunersThese are made from solid stainless steel and are not soft and weak like the brass screws.Also available in sets of 6 for $28.00$6.00 each screw HWft-1$6.00HWJKSLSJackson JT6 Or Kahler String Lock Shim These are the original thickness that cameon the JT6 and Kahler String Locks. Can also be used for the string locks I sell as wellESP PartsESP Logo'd Tremolo Saddle/String Locking ScrewsThese are the perfect replacements for your missing screws!Sold in sets of 6 for $5.00HWscw-26ESP Logo'd Tremolo Socket Set Screws These are correct fitting replacements withan Allen wrench socket so no more slipping off the head of the screw! .50 cents ea.HWscw-26SCSold in a set With Wrench $1.25HWscw-26SCWESP Logo'd Tremolo Socket Friction Bushing These are the correct fitting replacementSocket Friction Bushings. These install in thesocket, and then the set screw (above) creates pressure on the socket, then creating friction on your trem bar, thus allowing you to position the bar wherever you’d like.$10.00 ea.HWscw-26SB$1.00EachWashburn Wonderbar Shift 2001 PartsAllen Wrench for theWashburn Wonderbar Trem Front and Rear Height ScrewAdjustersYAMAHA Rockin' Magic II Fine TunersThese are made from solid stainless steel and are the correct thread. These have a nicer sized knob as well for easier gripping.$30.00 Per set of 6 HWYFT-1$6.00 1 to 5 Pieces HWYFT-1a