Jackson JT6 Bridge String Lock Screws!
Available now are these Replacement String Lock Screws for the Jackson JT6 Tremolos.
Remember, the whole reason these have to be replaced is because everyone seems to want to
over tighten this screw. There is no need for that ;o)
These are $4 each or a set of 6 for $17.00 or: The set of 6 with Allen Wrench is $18.00
As you can see in the pics, while they do look different, they're not bad at all and have
a nice black finish to match. I was going to start "kinking" the last thread near the wrench opening
but thought some of you might actually like the fact that the fine tuner can turn right off.
If you'd like this little feature, just give me a shout and let me know and I can do that for you so
you don't lose your fine tuner on stage ;o)
If you need the Allen wrench (3mm) for the
installation, I have those as well.
$1.00 Each
Original Floyd Rose Special Tremolo Bars
These will fit Original Floyd Rose, Floyd Rose Special, and Floyd Rose II tremolos with the
socket for the collared style bars. These come with a new socket to install into your bridge plate
in case yours is worn. Available in Gold, Chrome, Black, or Black for Left Handed.
TB-SFLR-B(Temporarily Unavailable)(Black) $31.00 each, TB-SFLR-G(Gold) $37.00 each, TB-
SFLR-C(Silver) $27.00 each, or TB-SFLR-BL (*lefty)(Lefty-Black) $31.00 each.
Finally a way to change the battery in your
Jackson JE**** Pre-amps or EMG equipped guitars!!
Click here for more details!
Jackson / Charvel JT6 Floyd Tremolo
Bushings Covers available!
These originally came on the earlier USA Models
that had the JT6 tremolo installed to cover
up the "sloppy" paint edge around the bushing hole.
These were lightly pressed into the paint
but would usually come lose and get lost
if removing the trem for maintenance.
Bushings without
bushing covers:
Bushings with the
Bushing covers
installed:
$10.00 per pair
JCH-2C
Brass & Aluminum Jack Plates !
The brass are not clear coated, this means that they will tarnish as it's brass, not gold plating.
White Pearl/B/W
$10 TRCjc-1
Silver Pearl/B/W
$10 TRCjc-2
Green Pearl/B/W
$10 TRCjc-3
Black Pearl/B/W
$10 TRCjc-4
Red Pearl/B/W
$10 TRCjcr-5
Original B/W/B
$10 TRCjc-6
Brass
$18 TRCjc-7
Brushed/W/B
$10 TRCjc-8
White/B/W
$10 TRCjcr-5
Polished Aluminum
$16.00 TRCjc-9
Black Brushed
Aluminum Anodized
$17.00 TRCjc-10
Strap Buttons, Screws & Felts can be found Here on the Body Parts Page
Full Triangle Truss Rod Covers (Screws are HERE!)
Arrowhead style for the JT6 type and Kahler Locknuts
Cavity Cover Plates
Brushed plastic covers look just like the
original Brushed black aluminum covers.
Any Style $14.00 each plate.
Covers Can be altered for the "Tremol-No"
Please Ask!
Polished Aluminum: $24.00 each plate
Economy Satin finish plastic plates just
like the originals
$14.00 each plate
Solid polished Brass: $27.00 each plate
Solid Brushed Brass: $27.00 each plate
Black Brushed Aluminum Anodized $25.00 each plate
(Also available in the Tremolo Cover as well!)
Back Cover Plate Screws can be found Here on the Body Parts Page
Neck Plates
The brass and aluminum are not clear coated This means that they will tarnish as it's brass, not gold plated.
These are made from solid 1/8th inch thick stock.
These are the standard Fender, Charvel Jackson Bolt pattern.
Solid Uncoated Brass Relic'd finish
$18.00 HWnp-1
Solid Uncoated Brass Brushed Finish:
$18.00 HWnp-2
Solid Brass Polished Finish:
$18.00 HWnp-3
Black Anodized Aluminum Finish
$17.00 HWnp-4
Solid Aluminum Polished Finish:
$16.00 HWnp-5
Solid Uncoated Aluminum Brushed Finish:
$15.00 HWnp-6
Black Plastic Backer Pads
for the neck plates are here!!
These will fit all my neckplates and other
standard Strat, Jackson and Charvel both
import and USA models.
$3.00 each HWnp-7
Charvel Surfcaster (JT490) Tremolo Bars! These also fit the tremolos on the ST Models
These are the hard to find tremolo bars for the JT490 Tremolo and are made from solid polished
stainless steel only. Will not rust peel or chip. TB-490 $30.00.
JT490 Tremolo:
"ST" Tremolo:
Non Tabbed Version Of the
arrohead for “solid”
string locks.
Replacement screws can be found here
Newer "Football" Jackplates
The brass are not clear coated
This means that they will tarnish as it's
brass, not gold plating.
Will fit Ibanez, Charvel, Jackson guitars
Aluminum Black Anodized, polished or brushed brass,
and polished or brushed
aluminum.
$18.00 Each:
Brass/Brushed
HWjp-4
Brass/Polished
HWjp-8
Brass/Relic'd
HWjp-9
Brushed/Aluminum:
HWjp-101
Polished/Aluminum:
HWjp-5
Black Brushed
Aluminum
HWjp-6
Satin Aluminum: $22.00 each plate
Engravings can also be done, please inquire!
Truss Rod Wrenches and Nuts
These Truss Rod wrenches (chrome plated steel) will
fit the original Import Charvel Truss Rod Nuts as well
as my new Truss Rod nuts .
Use a drop of oil as these are made to be a good tight fit!
(made from nickel plated Brass).
$6.00 HWTRW
Truss Rod Wrench (only)
Temporarily Unavailable
Truss Rod Nut (only)
$12.00 HWTRN
I can now offer a service that will allow you to mount a modern
Floyd Rose Special tremolo bar with the friction collar built in.
The only thing you have to do is remove your old tremolo socket and replace it with the new one
that I have modified to fit the hole where your old socket went.
Yes the bar is included!
Click for Tutorial
No more bushings for those of you who do not like them ;o)
TB-JT6CB(Black) $31.00 each, TB-JT6CG(Gold) $37.00 each, TB-JT6CCS(Silver) $27.00
each, or TB-JT6CBL (*lefty)(Lefty-Black) $31.00 each.
Service is now available for the JT6 Jackson Logo'd Tremolos
An example of a JT6 Tremolo:
**NOTE** Lefty bars can only be purchased in Black Chrome
Original B/W/B
Models 1,1A,1C, and 2B
$10 TRCjc-61
Model series slotted plastic covers
are also available as well.
Jackson/Charvel “JT490” or “ST”
and also
Ibanez Maxxas and S-440II GOTOH Bridges
These are hard to find
replacement screws for
these bridges
Intonation Screws 6 Pcs.
$10.00
Saddle Locking Screws
6 pcs. $4.00
Tremolo Bar Friction
Screw 1 pc. $1.00
Allen Wrench for
Jackson/Charvel “JT490” or “ST” and
Ibanez Maxxas and S-440II GOTOH Bridges
This is for the trem bar friction screw adjustment
location near the trem bar socket opening
$1.00
Each
New “Industrious” Pattern
These are milled to a grid pattern and can be anodized or just left natural.
JT6 Replacement Tremolo Bars
While these are not genuine Jackson/Charvel Parts,these are
a low cost alternative for those who want to do mild tremolo work. These
bars do not have much friction, and will “swing” freely in the socket.
Unfortunately the upgrade bushings are no longer available.
Available in chrome or black plated steel.
Black : TB-EDGBR $12.00
Chrome: TB-EDGCR $12.00
Faux Carbon Fiber (plastic): $18.00 each plate
