Jackson JT6 Bridge String Lock Screws!
Available now are these Replacement
String Lock Screws for the Jackson JT6 Tremolos. These will use a smaller allen
wrench that I will make available soon. Remember, the whole reason these have to
be replaced is because everyone seems to want to over tighten this screw.
There is no need for that ;o)
These are $4 each or a set of 6 for
$20.00
 
or
The set of 6
with Allen Wrench is
$21.00
As you can see in the pic below, while
they do look different, they're not bad at all and have a nice black finish to
match. I was going to start "kinking" the last thread near the wrench opening
but thought some of you might actually like the fact that the fine tuner can
turn right off. If you'd like this little feature, just give me a shout and let
me know and I can do that for you so you don't lose your fine tuner on stage ;o)
|
|
New Service is now available for the JT6 Jackson Logo'd Tremolos
shown below:
An example of a JT6 Tremolo:
**NOTE**
Black only for Lefties
Unfortunately these are NOT available
for left handers in Chrome or Gold as I do not make these bars, I
just modify the socket for the tremolo.
I can now offer a service that will allow
you to mount a modern Floyd Rose type tremolo bar with the friction
collar built in.
The only thing you have to do is remove
your old tremolo socket and replace it with the new one
that I have modified to fit the hole where
your old socket went.
No more bushings for those of you who do
not like them ;o)
|
Available in Gold, Chrome, and Black.
$27.00 each.
|
 
|
Check out the new item for you Jackson Charvel
Fans!
Finally a way to change the
battery in your Jackson JE**** Pre-amps or EMG equipped guitars!!
Click here for more details!
JT6 Tremolo Posts AND Bushings
These are available again due to high
demand, first come first serve!
|
JT6 / Floyd Rose Posts
These are for the early Jacksons and Charvels that came stock with the
JT6 Tremolo. The pivot angles match the Original Floyd Rose so you'll
get more "range" when diving. These are heat treated and then a black
oxide is applied as a rust preventative. A light coat of oil is
recommended.
|
$25.00 a Pair JCH-1 |
 |
|
Jackson / JT6 Floyd Tremolo Bushings now
available!
These are for the early Jackson's and Charvel's that came stock with the
JT6 Tremolo. They are the correct original threads and are slightly
oversized for a good press fit. NOTE* Please make sure your hole is not
too small as not to crack the body when pressing these in. I can not be
responsible for damage to the body. Please know what you're doing!
|
$20.00 a Pair
JCH-2 |
 |
|
Jackson / Charvel JT6 Floyd Tremolo Bushings
Covers
available!
These originally came on the earlier USA Models
that had the JT6 tremolo installed to cover up the "sloppy" paint edge
around the bushing hole. These were lightly pressed into the paint but
would usually come lose and get lost if removing the trem for
maintenance.
Bushings without bushing covers:
Bushings with the Bushing covers installed:
|
$8.00 per
pair |
 |
Full Triangle
Truss Rod Covers
Screws are
HERE!
Please note, Some Custom Shop guitars
had "custom" sized covers
so I may need a template from you for
proper fit.
|
White Pearl/B/W
$8.50
TRCjc-1
 |
Silver Pearl/W/B
$8.50
TRCjc-2
 |
Green
Pearl/B/W
$8.50
TRCjc-3
 |
Black Pearl/W/B
$8.50
TRCjc-4
|
|
Red Pearl/W
$8.50
TRCjc-16
 |
Original B/W/B
$7.00
TRCjc-6
 |
Polished
Brass
$16.00
TRCjc-7
 |
Black Brushed
B/W/B
$8.00
TRCjc-8
|
|
White/B/W
$7.00
TRCjc-5
|
Polished
Aluminum
$15.00
TRCjc-9
|
Black Grynd
Aluminum Anodized
$16.00
(pic soon)
|
Black Brushed
Aluminum Anodized
$16.00
TRCjc-10
|
Custom "RR" Truss Rod Covers
|
Black Brushed
Aluminum Anodized
"RR"
"Laser Engraved"
$20.00 ea.
TRCrr-1
TRCrr-2
|
Chrome Mirror "RR"
"Laser Engraved"
$20.00 ea.
These are engraved from the
back
allowing the top surface to
remain smooth
Very Sharp looking!
TRCrr-3
|
B/W/B Brushed "RR"
Engraved Truss Rod Covers
in Black or White
$16.00
TRCrr-4
|
"RR"
"Machine Engraved"
Brushed Black Anodized
Aluminum Truss Rod Covers
$20.00
TRCrr-5
TRCrr-6
|
|
"RR"
"Machine Engraved"
Polished Brass
and Aluminum Truss Rod Covers
$20.00
Brass-
TRCrr-7
Aluminum-
TRCrr-8
|
"RR"
"Machine Engraved"
Polished Brass
and Aluminum Truss Rod Covers
$20.00
Brass-
TRCrr-9
Aluminum-
TRCrr-10
 |
Black Brushed
Aluminum Anodized
Rolls Royce Font
"Machine Engraved"
$20.00 ea.
TRCrr-11
 |
"RR"
"Machine Engraved"
Brushed Aluminum Truss Rod Covers
$18.00
TRCrr-12
or with Black Anodized
Borders and RR's
$20.00
TRCrr-13
|
|
"RR"
"Machine Engraved"
in Pearloid Finishes
$18.00 each
TRCrr-14
TRCrr-15
TRCrr-16
TRCrr-17
|
"RR"
"Machine Engraved"
Polished or Satin Aluminum Truss Rod Covers
$20.00 each
TRCrr-18
TRCrr-19
 |
|
|
Arrowhead style for the JT6 type and Kahler Locknuts
|
Polished
Brass
$16.00
TRCjc-11
 |
B/W/B
$7.50
TRCjc-12
 |
White Pearl /B/W
$8.50
TRCjc-13
 |
| Black Brushed
Aluminum Anodized
$20.00
TRCjc-14
|
Red Brushed
Aluminum Anodized
$20.00
TRCjc-15
 |
|
Strap Buttons:
| Relic'd Brass $22.00
per pair
HWsb-1
|
Brass $22.00 per
pair
HWsb-2
 |
| Aluminum
$22.00 per pair
HWsb-3
 |
Black Anodized
Aluminum
$24.00 per pair
HWsb-4
|
Rhoads Control Plates and "V" string
through Plates
Can be made in Polished Brass or Aluminum or
a variety of plastics like you see on the truss rod covers above.
|
Polished Brass or Aluminum!
$32.00 Each Plate
 |
Black Brushed Aluminum Anodized just like the Originals!
$36.00 each Plate
|
These can also be customized to
any configuration you'd like.
For example:
|
Customized Control Layouts!
 |
Red Pearloid Laminate
|
|
Brushed Plastic for the Economy Minded!
|
|
Cavity Cover Plates
Just a note about the smaller "Dimas" style covers.
There are actually 2 sizes that were used through the years so please look at
the picture below and measure the
distance between the 2 holes as shown to make sure you get the correct sized
cover.
The "center to center" hole measurement should be either 5-3/4" or 5-5/16ths".
|
Brushed plastic covers look just
like
the original Brushed black
aluminum covers.
Any Style
$11.00 each.
|
Covers Can now be altered for the "Tremol-No"
Please Ask!
 |
|
Polished Aluminum:
$20.00 each plate
|
Original Satin finish
plastic plates
Tremolo Spring Covers
$8.00
|
|
Original Satin finish
plastic plates
Early San Dimas Style
$8.00
|
Original Satin finish
plastic plates
Larger Route Cover
$8.00
|
|
Solid polished Brass:
$23.00 each plate
|
Brushed Brass:
$20.00 each plate
|
"4 Hole" San Dimas/Ontario sized Plate Black Brushed
Aluminum Anodized
$23.00 each plate
|
Black Brushed
Aluminum Anodized
$23.00 each plate
Also available
in the Tremolo Cover as well!
|
|
USA Jackson KV or Double Rhoads
Black Brushed
Aluminum Anodized
$23.00 each plate
|
|
USA Charvel and Jackson
Back-plate Screws
.25 cents each
Kahler Pro, Standard, or Flyer Bars
These are made to be exactly as the originals were except with
a much nicer finish. These are available in stainless steel or the brass and
these have the same threaded configuration and the same bends for those that
wanted the original style.
$25.00 each
Pic of the Solid Hardened Brass on Kahler Pro
Pictured in Polished Stainless
Steel and Hardened Brass (matches gold!). It's better than chrome or
gold plating because it will never chip or peel or rust!
JT6
Bars are available now !
These are a great replacement for those
bars that have been lost or broken.
These are available in chrome (polished
stainless steel). I can also do these in a
brushed finish and the plastic bushings are available.
$28
Please note, these bushings will not fit
the original JT6 tremolo bars without modification so you must tell me what they
are for when ordering so I can modify them for you for proper fit!! They will,
however, fit the JT6 Bars and the Ibanez Edge bars that I make and the original
Edge bar as well with no modification.
$2.00 each
bushing.
An example of a JT6 Tremolo:
Example of an Original Ibanez Edge Tremolo Bar:
These were black from the factory.
Example of an Original JT6 Tremolo Bar:
These were chrome from the factory.
|
Older Oversized Oval "Strathead" Charvel Jackplates
made from the same very thin Aluminum
and then Black Anodized. |
 |
$18.00 Each
HWjp-3 |
|
Newer "Football" Jackplates
Will fit
Ibanez, Charvel, Jackson guitars Aluminum Black Anodized,
polished or brushed brass, and
polished or brushed
aluminum. Aluminum not shown. |
|
$18.00 Each
Brass/Brushed HWjp-4
Brass/Polished HWjp-8
Brass/Relic'd HWjp-9
Polished Aluminum: HWjp-5
Black:
HWjp-6 |
Neck Plates
(uncoated brass and aluminum)
These are made from solid 1/8th inch
thick stock.
These are the standard Fender, Charvel
Jackson Bolt pattern.
|
Solid Uncoated Brass
Relic'd finish
$14.00
HWnp-1
|
Solid Uncoated Brass
Brushed Finish:
$14.00
HWnp-2
|
|
Solid Brass Polished Finish:
$15.00 HWnp-3
|
Black Anodized Aluminum
Finish
$15.00
HWnp-4
 |
|
Solid Aluminum Polished Finish:
$15.00 HWnp-5
|
Solid Uncoated Aluminum
Brushed Finish:
$14.00
HWnp-6
|
|
New Black Plastic Backer Pads
for the neck plates are here!!
These will fit all my neckplates and
other
standard Strat,
Jackson and Charvel
both import and USA models.
$3.00 each
HWnp-7
|
Solid Uncoated Aluminum
Grynd Finish:
$14.00
HWnp-8
 |
