Jackson JT6 Bridge String Lock Screws!
Available now are these Replacement
String Lock Screws for the Jackson JT6 Tremolos. These will use a smaller allen
wrench that I will make available soon. Remember, the whole reason these have to
be replaced is because everyone seems to want to over tighten this screw.
There is no need for that ;o)
These are $4 each or a set of 6 for
$20.00
JCH-7
 
or
The set of 6
with Allen Wrench is
$21.00
JCH-7W
As you can see in the pic below, while
they do look different, they're not bad at all and have a nice black finish to
match. I was going to start "kinking" the last thread near the wrench opening
but thought some of you might actually like the fact that the fine tuner can
turn right off. If you'd like this little feature, just give me a shout and let
me know and I can do that for you so you don't lose your fine tuner on stage ;o)
|
Check out the new item for you Jackson Charvel
Fans!
Finally a way to change the
battery in your
Jackson JE**** Pre-amps or EMG equipped guitars!!
Click here for more details!
JT6 Tremolo Posts AND Bushings
These are available again due to high
demand, first come first serve!
|
JT6 / Floyd Rose Posts
These are for the early Jacksons and Charvels that came stock with the
JT6 Tremolo. The pivot angles match the Original Floyd Rose so you'll
get more "range" when diving. These are heat treated and then a black
oxide is applied as a rust preventative. A light coat of oil is
recommended.
|
$25.00 a Pair JCH-1 |
 |
|
Jackson / JT6 Floyd Tremolo Bushings now
available!
These are for the early Jackson's and Charvel's that came stock with the
JT6 Tremolo. They are the correct original threads and are slightly
oversized for a good press fit. NOTE* Please make sure your hole is not
too small as not to crack the body when pressing these in. I can not be
responsible for damage to the body. Please know what you're doing!
|
$20.00 a Pair
JCH-2 |
 |
|
Jackson / Charvel JT6 Floyd Tremolo Bushings
Covers
available!
These originally came on the earlier USA Models
that had the JT6 tremolo installed to cover up the "sloppy" paint edge
around the bushing hole. These were lightly pressed into the paint but
would usually come lose and get lost if removing the trem for
maintenance.
Bushings without bushing covers:
Bushings with the Bushing covers installed:
|
$8.00 per
pair |
 |
Full Triangle
Truss Rod Covers
(Temporarily unavailable with
clear coating on
polished brass and aluminum)
Screws are
HERE!
Please note, any early Model Series that
had vintage strat style tremolos,
had different sized truss rod cover
dimensions. Please let me know what Model you have
or you can a send a pic so
that I may help you get the correct one.
|
White Pearl/B/W
$8.50
TRCjc-1
 |
Silver Pearl/W/B
$8.50
TRCjc-2
 |
Green
Pearl/B/W
$8.50
TRCjc-3
 |
Black Pearl/W/B
$8.50
TRCjc-4
|
|
Red Pearl/W
$8.50
TRCjc-16
 |
Original B/W/B
$7.00
TRCjc-6
 |
Polished
Brass
$16.00
TRCjc-7
 |
Black Brushed
B/W/B
$8.00
TRCjc-8
|
|
White/B/W
$7.00
TRCjc-5
|
|
Polished
Aluminum
$15.00
TRCjc-9
 |
Black Brushed
Aluminum Anodized
$16.00
TRCjc-10
|
Arrowhead style for the JT6 type and Kahler Locknuts
|
Polished
Brass
$16.00
TRCjc-11
 |
B/W/B
$7.50
TRCjc-12
 |
White Pearl /B/W
$8.50
TRCjc-13
 |
| Black Brushed
Aluminum Anodized
$20.00
TRCjc-14
|
|
|
Truss rod cover and
tuner screws
Strap Buttons:
| Relic'd Brass $22.00
per pair
HWsb-1
|
Brass $22.00 per
pair
HWsb-2
 |
| Aluminum
$22.00 per pair
HWsb-3
 |
Black Anodized
Aluminum
$24.00 per pair
HWsb-4
|
Cavity Cover Plates
(Temporarily unavailable with
clear coating on
polished brass and aluminum)
When ordering covers, please let me know if this is a "recessed into the body"
type cover or
if
it mounts to the "surface of the body".
These can be done in different materials also. These were for
a Model Series Charvel :
|
Brushed plastic covers look just
like
the original Brushed black
aluminum covers.
Any Style
$11.00 each.
|
Original Satin finish
plastic plates
Tremolo Spring Covers
$8.00
|
|
Polished Aluminum:
$20.00 each plate
|
Original Satin finish
plastic plates
Tremolo Spring Covers
Cut for Tremol-No
$13.00
|
|
Original Satin finish
plastic plates
Early San Dimas Style
$8.00
|
Original Satin finish
plastic plates
Larger Route Cover
$8.00
|
|
Solid polished Brass:
$23.00 each plate
|
Brushed Brass:
$20.00 each plate
|
|
|
Black Brushed
Aluminum Anodized
$23.00 each plate
Also available
in the Tremolo Cover as well!
|
|
Original "Paddle" style pickup and boost switches
These are used as the pickup switches on Model 6's
and 4's and were also used on the boost systems
and other electronics used by Jackson/Charvel
guitars.
Recently I
had a customer complain that this is a double pole switch, and not a
single pole. Just for your info, double pole switches were also used in
the Model 4's and 6's, it just depends on the year of production. They
still wire up the same way, the double pole just gives more options. |
$12.00
each HWsw-1 |
 |
|
Solid Brass Grounding Plates
So far, these are available for all Model Series
Charvels, Usa Ontario Cavities (3 & 4 hole), Original Dimas Cavity and
King V cavities. (I don't
have the smaller triangle cavity used in the 90's and some soloists as
of yet.) |
$6.00
each JCH-6 |
 |
Kahler Trem Arms for Kahler Pro, Kahler Standard,
Kahler Bass or
Kahler Traditional Vintage Series
These are made from solid Stainless Steel or Solid Brass,
polished to a high luster or Satin Brushed.
$28.00
Picture Of a Kahler Pro Tremolo
Picture of The Kahler Traditional Series Tremolo
|
New Service is now available for the JT6 Jackson Logo'd Tremolos
shown below:
An example of a JT6 Tremolo:
**NOTE**
Black only for Lefties
Unfortunately these are NOT available
for left handers in Chrome or Gold as I do not make these bars, I
just modify the socket for the tremolo.
Click for New Tutorial
I can now offer a service that will allow
you to mount a modern Floyd Rose type tremolo bar with the friction
collar built in.
The only thing you have to do is remove
your old tremolo socket and replace it with the new one
that I have modified to fit the hole where
your old socket went.
No more bushings for those of you who do
not like them ;o)
|
Available in Gold, Chrome, and Black.
$27.00 each.
|
 
|
|
If you need the Allen wrench (3mm) for the
installation, I have those as well. |
M3(3mm) Allen wrench $1.00 |
 |
Charvel Surfcaster Tremolo Bars!
These are the hard to find tremolo bars
for the JT490 Tremolo as pictured below.
These are made from solid polished
stainless steel and will not rust peel or chip.
$25.00
JT490 Tremolo:
Neck Plates
(uncoated brass and aluminum)
These are made from solid 1/8th inch
thick stock.
These are the standard Fender, Charvel
Jackson Bolt pattern.
|
Solid Uncoated Brass
Relic'd finish
$14.00
HWnp-1
|
Solid Uncoated Brass
Brushed Finish:
$14.00
HWnp-2
|
|
Solid Brass Polished Finish:
$15.00 HWnp-3
|
Black Anodized Aluminum
Finish
$15.00
HWnp-4
 |
|
Solid Aluminum Polished Finish:
$15.00 HWnp-5
|
Solid Uncoated Aluminum
Brushed Finish:
$14.00
HWnp-6
|
|
New Black Plastic Backer Pads
for the neck plates are here!!
These will fit all my neckplates and
other
standard Strat,
Jackson and Charvel
both import and USA models.
$3.00 each
HWnp-7
|
Solid Uncoated Aluminum
Grynd Finish:
$14.00
HWnp-8
 |
|
Older Oversized Oval "Strathead" Charvel Jackplates
made from the same very thin Aluminum
and then Black Anodized. |
 |
$18.00 Each
HWjp-3 |
|
Newer "Football" Jackplates
Will fit
Ibanez, Charvel, Jackson guitars Aluminum Black Anodized,
polished or brushed brass, and
polished or brushed
aluminum. Aluminum not shown. |
|
$18.00 Each
Brass/Brushed HWjp-4
Brass/Polished HWjp-8
Brass/Relic'd HWjp-9
Polished Aluminum: HWjp-5
Black:
HWjp-6 |
